PWM Control of a Buck Converter with an Amorphous Core Coil

Pulse-width modulation is widely used to control electronic converters. One of the most topologies used for high DC voltage/low DC voltage conversion is the Buck converter. It is obtained as a second order system with a LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core instead of air core lets design converters with smaller size. If high switching frequencies are used for obtaining high quality voltage output, the value of the auto inductance L is reduced throughout the time. Then, robust controllers are needed if the accuracy of the converter response must not be affected by auto inductance and load variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a not-toohigh switching frequency is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results are presented

Using the Own Flexibility of a Climbing Robot as a Double Force Sensor

Force sensors are used when interaction tasks are carried out by robots in general, and by climbing robots in particular. If the mechanics and electronics systems are contained inside the own robot, the robot becomes portable without external control. Commercial force sensors cannot be used due to limited space and weight. By selecting the links material with appropriate stiffness and placing strain gauges on the structure, the own robot flexibility can be used such as force sensor. Thus, forces applied on the robot tip can be measured without additional external devices. Only gauges and small internal electronic converters are necessary. This paper illustrates the proposed algorithm to achieve these measurements. Additionally, experimental results are presented

Robust control of underactuated wheeled mobile manipulators using GPI disturbance observers

This article describes the design of a linear observer–linear controller-based robust output feedback scheme for output reference trajectory tracking tasks in the case of nonlinear, multivariable, nonholonomic underactuated mobile manipulators. The proposed linear feedback scheme is based on the use of a classical linear feedback controller and suitably extended, high-gain, linear Generalized Proportional Integral (GPI) observers, thus aiding the linear feedback controllers to provide an accurate simultaneous estimation of each flat output associated phase variables and of the exogenous and perturbation inputs. This information is used in the proposed feedback controller in (a) approximate, yet close, cancelations, as lumped unstructured time-varying terms, of the influence of the highly coupled nonlinearities, and (b) the devising of proper linear output feedback control laws based on the approximate estimates of the string of phase variables associated with the flat outputs simultaneously provided by the disturbance observers. Simulations reveal the effectiveness of the proposed approach

A generalized method for flat plates impact detection and location

In the last years, many analyses from acoustic signal processing have been used for different applications. In most cases, these sensor systems are based on the determination of times of flight for signals from every transducer. This paper presents a flat plate generalization method for impact detection and location over linear links or bars-based structures. The use of three piezoelectric sensors allow to achieve the position and impact time while the use of additional sensors lets cover a larger area of detection and avoid wrong timing difference measurements. An experimental setup and some experimental results are briefly presented

Space-state robust control of a Buck converter with amorphous core coil and variable load

Pulse-width modulation is widely used to control electronic converters. One of the most frequently used topologies for high DC voltage/low DC voltage conversion is the Buck converter. These converters are described by a second order system with an LC filter between the switching subsystem and the load. The use of a coil with an amorphous magnetic material core rather than an air core permits the design of smaller converters. If high switching frequencies are used to obtain high quality voltage output, then the value of the auto inductance L is reduced over time. Robust controllers are thus needed if the accuracy of the converter response must be preserved under auto inductance and payload variations. This paper presents a robust controller for a Buck converter based on a state space feedback control system combined with an additional virtual space variable which minimizes the effects of the inductance and load variations when a switching frequency that is not too high is applied. The system exhibits a null steady-state average error response for the entire range of parameter variations. Simulation results and a comparison with a standard PID controller are also presented

Force sensor of a climbing robot derived from its own flexible structure

One of the most important design constraints of a climbing robot is its own weight. When links or legs are used as a locomotion system they tend to be composed of special lightweight materials, or four-bars-linkage mechanisms are designed to reduce the weight with small rigidity looses. In these cases, flexibility appears and undesirable effects, such as dynamics vibrations, must be avoided at least when the robot moves at low speeds. The knowledge of the real tip position requires the computation of its compliance or stiffness matrix and the external forces applied to the structure. Gravitational forces can be estimated, but external tip forces need to be measured. This paper proposes a strain gauge system which achieves the following tasks: (i) measurement of the external tip forces, and (ii) estimation of the real tip position (including flexibility effects). The main advantages of the proposed system are: (a) the use of external force sensors is avoided, and (b) a substantial reduction of the robot weight is achieved in comparison with other external force measurement systems. The proposed method is applied to a real symmetric climbing robot and experimental results are presented

Encuesta de evaluación de la "usabilidad" de la sede web de la Biblioteca Universitaria de Córdoba

Comunicación presentada a las XV Jornadas Bibliotecarias de Andalucía: Bibliotecas, rompiendo barreras, tejiendo redes. Córdoba, 15-17, Octubre, 2009La unión cada vez más estrecha entre la biblioteca universitaria y su sede web es incuestionable. Este trabajo es un estudio de usabilidad de la sede web de la Biblioteca Universitaria de Córdoba. El estudio se ha llevado a cabo realizando una encuesta de evaluación entre dos grupos de usuarios/alumnos, con dos ediciones sucesivas de la página, y un tercer grupo de usuarios/expertos, con la última edición. Los resultados obtenidos muestran considerables diferencias en la forma de interactuar con el sitio web entre los dos primeros grupos de usuarios con respecto al tercero. El estudio de usabilidad ha sido una herramienta muy útil que, además, nos permitirá desarrollar futuras mejoras del sitio web que cumplan con las necesidades y expectativas de los usuarios

Teaching automatic control in non-specialist engineering schools

Automatic Control Teaching in the new degree syllabus has reduced both, its contents and its implementation course, with regard to traditional engineering careers. On the other hand, where the qualification is not considered as automatic control specialist, it is required an adapted methodology to provide the minimum contents that the student needs to assimilate, even in the case that students do not perceive these contents as the most important in their future career. In this paper we present the contents of a small automatic course taught Naval Architecture and Marine Engineering Degrees at the School of Naval Engineering of the Polytechnic University of Madrid. We have included the contents covered using the proposed methodology which is based on practical work after lectures. Firstly, the students performed exercises by hand. Secondly, they solve the exercises using informatics support tools, and finally, they validate their previous results and their knowledge in the laboratory platforms

Comparativa y Analisis de Variabilidad Espacial entre las Medidas de Radiacion Solar Terrestres (SIAR) y Satelitales (CMSAF)

El objetivo de este trabajo es el análisis comparativo de dos fuentes de irradiación solar para el territorio peninsular español, siguiendo la iniciativa de estudios previos para otras regiones. La primera de estas fuentes corresponde a medidas de irradiación global diaria en el plano horizontal realizadas por los piranómetros de la red de estaciones meteorológicas del Sistema de Información Agroclimática del Regadío (SIAR), perteneciente al Ministerio de Medio Ambiente, Rural y Marino. Esta red está compuesta por más de 360 estaciones ubicadas en once Comunidades Autónomas de la España peninsular. La otra fuente de comparación es un conjunto de imágenes de satélite proporcionadas por la iniciativa denominada ``The Satellite Application Facility on Climate Monitoring'' (CM-SAF)

Nueva etapa: idénticos objetivos, mejor contexto

Se expone el significado del cambio al entorno digital de la Revista Ingeniería del AguaCabrera Marcet, E.; Dolz Ripolles, J.; Morales Baquero, R.; Rodríguez Sinobas, L.; Roldan Cañas, J. (2014). Nueva etapa: idénticos objetivos, mejor contexto. Ingeniería del agua. 18(1). https://doi.org/10.4995/ia.2014.3289OJSV18